A liquid cooling cold plate lives or dies in its channels. Etching makes those channels without a cutting tool — no milling marks, no burrs, no tool wear — but it also imposes its own design rules, and a channel layout drawn for milling will not always etch well. Xinketching is a precision photochemical etching manufacturer in Dongguan, China, producing flat etched metal parts since 2005. This guide sets out the design-for-manufacture rules for etched cold plates: depth, width, walls, ports, manifolds and flatness, and what to put on the drawing.
Answer capsule: five DFM rules for etched cold plates
- Depth is a half-etch. Channels are etched to 50–75% of sheet thickness with depth control of ±0.05 mm — specify the depth, and expect it uniform across the whole plate.
- Ports follow the thickness rule. Through-holes for ports and mounting follow the through-feature floor of ≈ 0.8–1.2× material thickness; a port much smaller than the stock will not break through cleanly.
- Walls are sealing lands. The metal left between channels carries the gasket — confirm land width at drawing review rather than drawing it as an afterthought.
- Manifolds etch in the same pass. Distribution manifolds, ports and alignment features come from the same artwork as the channels — no second machining setup, no datum shift.
- Flatness is a process property. Etching adds no mechanical stress and no heat, so the plate comes off the sheet flat — but the format is flat sheets only, 600 × 1,450 mm maximum, with full size only for material 0.5 mm and above.
Specifications
- Materials: stainless steel, copper, nickel, titanium (we do not etch aluminium)
- Thickness range: 0.05–2.5 mm — gauges 0.05, 0.08, 0.1, 0.12, 0.15, 0.2, 0.25, 0.3, 0.4 and 0.5 mm are stocked; above 0.5 mm up to 2.5 mm is sourced per order
- Channel depth: half-etch, 50–75% of thickness, depth control ±0.05 mm
- Through-features (ports, mounting holes): ≈ material thickness (design rule ≈ 0.8–1.2× thickness)
- Dimensional tolerance: ±10% of material thickness; raw-stock thickness tolerance ±0.02 mm
- Format: flat sheets only, no coil/reel-to-reel; maximum single sheet 600 × 1,450 mm for material 0.5 mm and above; thinner gauges run smaller formats
- Finishing: passivation in-house; plating via qualified partners
- Lead times and order terms: samples 3–5 days, production 7–10 days; no minimum order quantity, minimum order charge US$100; FOB
- Quality documents: material test certificate with per-run material batch traceability; PPAP Level 3 supported; IMDS data available; NDAs on request
Rule 1: specify channel depth, and expect it everywhere
An etched channel is a half-etched recess, not a milled slot. Its depth is set as a fraction of the sheet — 50–75% of thickness — and held to ±0.05 mm across the plate. That uniformity is the thermal point: a channel that runs shallow in one corner starves that corner of coolant and creates a hot spot above it, and no downstream inspection can fix a depth error that is baked into the plate. On the drawing, give the channel depth as a number and the tolerance as the half-etch control, not as a general tolerance block — and if the design needs two different depths on one plate, say so, because depth is an artwork decision made before etching, not an adjustment made after it.
Rule 2: ports and holes obey the thickness rule
Channels are blind features; ports, inlets, outlets and mounting holes are through-features, and through-features obey the floor: roughly the material thickness, 0.8–1.2× as a rule of thumb. A 0.2 mm port in 0.5 mm stock will not etch cleanly, however good the channel layout is. Where a design needs a small port in thick stock, the honest fixes are a thinner plate, a larger port, or a two-piece arrangement — all drawing decisions, and all cheaper to make before samples than after them. Ports etched in the same pass as the channels also carry a benefit worth using: because they come from the same artwork, port-to-channel alignment is set by the artwork itself, with no second setup to drift.
Rule 3: walls between channels are sealing lands, not leftover metal
It is tempting to pack channels as tightly as the pattern allows. Resist it where the plate will be sealed: the land between two channels is what the gasket sits on, and a land too narrow to support the gasket will leak under pressure regardless of how good the channels are. There is no universal land-width number — it depends on the seal design and the operating pressure — so confirm it at drawing review with the seal in mind, and keep the land continuous around ports and at the plate edge. The same thinking applies to the plate edge itself: leave a sealing margin around the full outline rather than running channels to the edge.
Rule 4: put the manifold in the plate
A cold plate with a bolted-on or bonded distribution manifold carries extra layers, extra joints and extra leak paths. Etching removes that bargain: the manifold, the distribution channels and the ports can all be etched in the same pass, from the same artwork, at the same depth control. The result is one plate with no bonded layers in the flow path. One boundary belongs here, stated plainly: we supply the etched plate itself. Sealing, bonding and brazed assemblies are the customer’s own downstream steps — the plate arrives ready for your seal, not as a sealed assembly.
Rule 5: flatness, size and material follow the format
Etching adds no mechanical stress and no heat, so a cold plate comes off the sheet flat and stays flat — an advantage over milled plates, which can move when material is removed. But the format is flat sheets only: a maximum single sheet of 600 × 1,450 mm, and that full size only for material 0.5 mm and above; thinner gauges run smaller formats to stay flat. On material: copper for conductivity, stainless steel for corrosion resistance and pressure, titanium where aggressive chemistry is in play — and no aluminium, which we do not etch. If the plate must be larger than one sheet, that is a design conversation about joints and tiling, not a reason to expect a bigger etch bath.
The drawing checklist for a cold plate
Material and grade; sheet thickness; channel layout with depth specified; port positions and diameters checked against the thickness rule; land widths around channels and ports; sealing margin at the outline; finish (passivation, or a plating specification through our partners); quantity and repeat pattern; operating pressure and coolant, so the land and material choice can be checked. A drawing that carries those items gets a firm quotation and a first sample in 3–5 days; a drawing that carries only an outline gets a round of questions first.
What etching does not do for cold plates
We do not machine thick blocks, braze assemblies, apply fuel-cell coatings or supply on reels. A cold plate that needs a thick machined manifold block, a brazed joint or a coated flow field belongs with a different process — and a quotation that pretends otherwise will fail at validation. What etching does, and does better than milling for this product, is put uniform, burr-free channels into a thin flat plate with no tooling and no tool wear, and revise that pattern in days when the thermal design moves.
FAQ
What channel depth should I specify?
A half-etch at 50–75% of sheet thickness, held to ±0.05 mm. Give the depth as a number on the drawing.
Can ports be smaller than the plate thickness?
No — through-features floor at roughly the material thickness. Thin the plate, enlarge the port, or split the design.
Do you supply the sealed cold plate assembly?
No. We supply the etched plate itself; sealing and assembly are your downstream steps.
How large a cold plate can you etch?
A single flat sheet up to 600 × 1,450 mm, full size only for material 0.5 mm and above; thinner gauges run smaller.
Can the manifold be part of the etched plate?
Yes. Manifolds, channels, ports and alignment features etch in one pass from one artwork, with no bonded layers in the flow path.
Send the channel layout
Xinketching etches cold plates in stainless steel, copper, nickel and titanium from 0.05 to 2.5 mm, with samples in 3–5 days, production in 7–10 days, no minimum order quantity and a US$100 minimum order charge. Send the channel layout through our contact page or to sales@xinketching.com, and we will check it against the five rules above before quoting.
- What Does a 770 W/cm² GPU Hotspot Mean for the Etched Copper Flow Layer? - November 22, 2026
- Photo-Etched Precision Medical Metal Components: Micro-Needles, Lancets and Microfluidic Parts - November 21, 2026
- Custom Lead Frame Etching for IC Packaging: Photo-Etched vs Stamped Lead Frames - November 18, 2026








