A satellite is the one product that can never come back to the workshop. Once it is launched, a part that is a fraction of a millimetre out, a bracket that does not sit flat, or a shim that was meant to level an optical bench stays wrong for the whole mission. That is the discipline behind every satellite drawing, and it is why the manufacturing question matters more here than in almost any other titanium application: which parts can be made by photo-chemical etching, and which must be made another way?
The industry’s own evidence says etched parts are already inside satellite assemblies. PEI — Photofabrication Engineering Inc. — states on its defense-industry page that it “routinely produces parts … including precision shims used by defense and aerospace contractors to level or balance systems like missiles, optics, avionics, and satellite assemblies”, and that its components “can be found in hundreds of defense programs — from satellite assemblies to battlefield communication systems”. Fotofab’s military-defense page lists the same territory from the other side: titanium-based alloys among the metals it etches, and satellite components among the applications, alongside avionics, UAV drones and unmanned ground vehicles. Neither page is ours, and neither is a supply claim for us — they are the reason a buyer asks the question, and the question this post answers: which flat titanium parts in a satellite or space assembly suit etching, and what must the drawing carry when there is no second chance?
The short answer is the same as every other day this week, with one difference that changes how seriously the drawing is taken. The etched parts are flat: the alignment shim, the avionics bracket, the aperture plate, the sensor mounting plate, the cover panel. A buyer who sends us a satellite bus structure will be told no; a buyer who sends us a shim drawing will be quoted. The rest of this post is the line between the two, and the four things the drawing must carry on the etched side of it.
Answer capsule: six things a buyer needs
- We etch titanium satellite parts — flat ones. Titanium is one of the five metals we photo-etch — stainless steel, titanium, copper, brass and nickel. We do not etch aluminium.
- The etched parts are shims, brackets, aperture plates, sensor plates and cover panels. Flat, thin, fine-detailed — that is the etching envelope, and a satellite alignment shim sits squarely inside it.
- No second chance means the drawing does the work. A satellite part cannot be reworked in orbit, so the drawing must state material and grade, thickness, tolerance and finish, and inspection — before the first article is cut, not after.
- Tolerance is ±10% of thickness. On 0.1 mm stock that is ±0.01 mm; on 0.2 mm stock, ±0.02 mm; on 0.5 mm stock, ±0.05 mm. Thickness is the number the shim, the bracket and the flatness are built around.
- Through-features follow the thickness rule. A hole or slot floors at roughly 0.8–1.2× the material thickness. Finer detail needs thinner stock, not a harder etch.
- Flat parts only, to 600 × 1,450 mm. We etch flat sheets; full size only at 0.5 mm and above, thinner gauges run smaller. A part that needs a bend or a formed feature is a formed part: bending/forming is outsourced and must be confirmed at quotation.
Specifications
- Materials: stainless steel, titanium, copper, brass and nickel (we do not etch aluminium)
- Titanium grades etched: commercially pure Grades 1 and 2 and alloy Grade 5 (Ti-6Al-4V); other grades confirm at quotation
- Thickness range: 0.05–2.5 mm — gauges 0.05, 0.08, 0.1, 0.12, 0.15, 0.2, 0.25, 0.3, 0.4 and 0.5 mm stocked; above 0.5 mm up to 2.5 mm sourced per order
- Maximum flat sheet: 600 × 1,450 mm — full size only at 0.5 mm and above; thinner gauges run smaller
- Tolerance: ±10% of material thickness (on 0.1 mm stock ±0.01 mm; on 0.2 mm stock ±0.02 mm; on 0.5 mm stock ±0.05 mm)
- Half-etch (recessed markers, identification, stepped relief): 50–75% of thickness, depth control ±0.05 mm
- Through-features (mounting holes, apertures, slots): ≈ 0.8–1.2× material thickness minimum (55 × 180 µm through-slots in 0.3 mm stock declined as below the rule)
- Form: flat sheets only — no coil, no reel; bending/forming outsourced
- Finish: passivation available in-house; plating and surface treatment outsourced
- Documentation: material test certificate + per-run batch numbers on every order; PPAP Level 3 documentation available. We do not hold AS9100 or ITAR registration; space qualification (radiation, thermal-vacuum, outgassing) is the buyer’s, not ours
- Lead time: samples 3–5 days when material is in stock (7–10 days for special material not stocked); production 7–10 days
- Commercial: no MOQ; US$100 minimum order; FOB
Why titanium goes to space hardware
Three properties put titanium in a satellite, and none of them is fashion. The first is weight: at ≈ 4.5 g/cm³ against steel at ≈ 7.9 g/cm³, the same part in titanium weighs roughly 57% of the steel part. On a launch, every gram is paid for, and a bracket that does the same job at little more than half the weight is not a marginal gain. The second is corrosion resistance: titanium carries its own passive oxide layer, so a part that must sit for years without maintenance does not depend on a coating that can chip or wear. The third is that etching does not change the metal: photo-chemical etching removes material through a photographic mask with no mechanical force and no heat-affected zone, so the flat part that comes off the line keeps the base metal’s properties — the point PEI makes for its own defense work, and the reason etching suits a shim whose whole job is to stay exactly the thickness it was made.
The environment is what separates this post from the 11-12 aircraft post. An aircraft bracket lives in air and comes home for service; a satellite part lives in vacuum, cycles between sun and shadow, and is never touched again. That does not change which parts etching can make — the envelope is the same flat sheet, the same thickness rule, the same tolerance — but it changes what the buyer must put on the drawing. A tolerance that is generous on an aircraft bracket can be the difference between an aligned instrument and a misaligned one in orbit, and a finish that is cosmetic on the ground can be the difference between a part that survives and one that does not. The drawing, not the process, carries that weight — which is why the four drawing items below are written as requirements, not suggestions.
Which satellite parts are etched
Alignment shims. The shim is the satellite part etching was made for. An optical bench, a sensor mount or an antenna assembly is levelled and spaced with thin flat shims, often in stepped sets of several thicknesses, and PEI’s own description — shims “used by defense and aerospace contractors to level or balance systems like missiles, optics, avionics, and satellite assemblies” — is the use case in one sentence. A shim is flat, thin, and judged entirely on its thickness and its edge: no burr, no distortion, identical from the first piece to the hundredth, because the pattern is photographed into the metal from one artwork. Our titanium guide covers grade choice in general; for a shim, Grade 2 is the usual corrosion-first choice, Grade 5 the higher-strength choice where the shim carries a load. Our aircraft shims and brackets post covers the same part in an atmosphere that comes home for service; the satellite version is the same envelope with a drawing that cannot afford a second chance.
Avionics brackets. A flat titanium bracket that holds an electronics module, a sensor or a cable run is an etched part when it is flat: mounting holes at the thickness rule, lightening cutouts where the drawing allows them, a burr-free edge where a wire or a flex circuit passes. The bracket that needs a bent flange or a formed stiffener is a formed part — bending is outsourced and must be confirmed at quotation — but the flat blank, with all its holes and outline, is etched first.
Aperture and sensor mounting plates. A plate that carries an optical aperture, a sensor window or a detector mount is a flat etched part: through-apertures at the thickness rule, half-etched recesses for seating at 50–75% of thickness with ±0.05 mm depth control, and a flatness that comes from the sheet, not from machining. The same envelope covers the cover panel — a flat titanium panel with vent or fastener holes that closes an electronics bay.
Shield and divider elements. Where a flat divider or shield element inside an electronics enclosure is specified in titanium — for corrosion and strength rather than for conductivity — it is etched like any other flat panel. Note the boundary: copper conducts better, so where shielding effectiveness is the first requirement, the honest answer is copper or a copper alloy, not titanium.
What is not etched. The satellite bus structure, a pressure vessel, a propellant tank, a threaded fastener, a hinge or deployment mechanism, a machined housing with a blind hole that must hold a screw, and any assembled avionics box. Anything with a thread, a bearing seat, a thick wall or a three-dimensional form is a machined part. Sending us one of those drawings will get a polite no and a referral to the right process — which is better than a yes that ships a part that does not work, and in space there is no workshop to fix it in.
The no-second-chance rule, in practice
“No second chance” is not a slogan; it is a way of writing the drawing. On the ground, a bracket that is 0.02 mm out can be shimmed, filed or remade in an afternoon. In orbit it is a permanent error. The practical consequences for the buyer are three.
First, prove the part on the ground before committing the flight quantity. Samples run 3–5 days when the material is in stock, and the sample is where the drawing is tested: fit, flatness, hole positions, edge quality. A sample that fails on the bench is cheap; the same failure in orbit is total. Use the sample run.
Second, state the operating environment on the drawing. Etching does not change the base metal, but the buyer — not the etcher — decides whether Grade 2 or Grade 5 is right for the temperature swings and the mission life, and whether passivation or an outsourced surface treatment is specified. A drawing that says nothing about environment leaves the most important decision to guesswork.
Third, do not ask the etcher to qualify the part for space. We supply the flat part with a material test certificate, per-run batch numbers and PPAP Level 3 documentation where requested. Radiation, thermal-vacuum and outgassing qualification are test programmes the buyer runs; we do not hold AS9100 or ITAR registration, and this post does not claim otherwise. A supplier who offers space qualification as a line item on an etch quote has not understood either the qualification or the etch.
What the drawing must carry
- Material and grade. Titanium, and which grade — commercially pure Grade 1 or 2, or alloy Grade 5 (Ti-6Al-4V). State it; do not leave it to the shop to guess. Other grades confirm at quotation.
- Thickness and the feature rule. State the stock thickness, and check every through-feature against it: a hole or slot floors at roughly 0.8–1.2× the thickness. On 0.1 mm stock that is roughly a 0.08–0.12 mm feature; on 0.2 mm stock, roughly 0.16–0.24 mm. A 55 × 180 µm through-slot in 0.3 mm stock was declined on this ground — finer detail needs thinner stock, not a harder etch.
- Tolerance and finish. Tolerance is ±10% of thickness on every dimension — on 0.1 mm stock ±0.01 mm, on 0.5 mm stock ±0.05 mm. State the finish: passivation in-house, or plating/surface treatment outsourced. State the operating environment the finish must survive.
- Inspection. State what is measured and how: hole positions, flatness, thickness, edge condition. Per-run batch numbers and a material test certificate come with every order; PPAP Level 3 is available where the programme requires it.
Frequently asked questions
Can you etch a satellite part?
We can etch the flat titanium parts that go into a satellite assembly — alignment shims, brackets, aperture plates, sensor mounting plates, cover panels. We cannot etch the satellite, the bus structure, a pressure vessel or an assembled avionics box. Send the flat-part drawing and it will be quoted; send the structure drawing and it will be declined with a referral.
What titanium grades do you etch?
Commercially pure Grades 1 and 2 and alloy Grade 5 (Ti-6Al-4V) are our standard range. Grade 2 is the usual corrosion-first choice, Grade 5 the higher-strength choice. Other grades confirm at quotation — do not read this post as a claim for every titanium grade.
What tolerance can we hold on a shim?
±10% of material thickness. On 0.1 mm stock that is ±0.01 mm; on 0.2 mm stock, ±0.02 mm; on 0.5 mm stock, ±0.05 mm. PEI’s published ±0.0005 in. figure is PEI’s capability, not ours — do not specify it to us.
How small can a hole be?
Roughly 0.8–1.2× the material thickness. On 0.1 mm stock, roughly 0.08–0.12 mm; on 0.3 mm stock, roughly 0.24–0.36 mm. Below that, use thinner stock or another process.
Do you qualify parts for space — radiation, thermal-vacuum, outgassing?
No. Qualification is the buyer’s test programme. We supply the part with a material test certificate, per-run batch numbers and PPAP Level 3 where requested. We do not hold AS9100 or ITAR registration.
How fast can we get a first article?
Samples in 3–5 days when the material is in stock, 7–10 days for special material not stocked; production 7–10 days. No MOQ, US$100 minimum order, FOB.
The satellite rule is the simplest one in this whole week: the part that can never be fixed must be right the first time, and “right the first time” is a property of the drawing, not of the process. Etching gives you a flat titanium part with no burr, no heat-affected zone and the same dimensions from the first piece to the hundredth. The drawing gives you the grade, the thickness, the tolerance and the inspection that make that part the right one. Send the drawing with those four items on it, prove it with a sample on the ground, and the part that flies is the part you meant to make.
- What Does a 770 W/cm² GPU Hotspot Mean for the Etched Copper Flow Layer? - November 22, 2026
- Photo-Etched Precision Medical Metal Components: Micro-Needles, Lancets and Microfluidic Parts - November 21, 2026
- Custom Lead Frame Etching for IC Packaging: Photo-Etched vs Stamped Lead Frames - November 18, 2026








