On October 27, 2026, iSpring Water Systems announced the BRO900, an onboard seawater desalination system for boats, yachts, coastal homes and off-grid use. It is a five-stage system, and the first thing seawater meets in it is a mesh filter. The release describes the stages in order: a stainless-steel mesh filter that “traps large particles like sand, shell fragments, and marine debris”, then a 20-micron PP filter, then a 5-micron PP filter, then a high-pressure reverse-osmosis membrane, then a LED UV module. The system produces up to 900 gallons per day at a working pressure of 800 psi, with a booster pump raising pressure to 600–900 psi to push seawater through the membrane. The mesh in the BRO900 is stainless steel, not titanium, and iSpring is not our customer — but the design decision is the news, and it is the question this post answers: when a filtration system puts a mesh first, what does the mesh actually have to do, and what does an etched titanium mesh offer that a woven one does not?
The short answer is that the mesh decides whether everything downstream survives. A membrane that clogs with sand and shell fragments is a membrane replaced early; a pre-filter whose apertures are uniform, whose edges do not fray, and whose material does not corrode in seawater is a pre-filter that can be cleaned and used again instead of thrown away. That is the whole case for etched titanium mesh, and it is also its limit: etched mesh is the coarse, repeatable, cleanable first stage — not the 20-micron stage and not the membrane. The rest of this post is the line between the two, and the three numbers that decide it.
Answer capsule: six things a buyer needs
- We etch titanium mesh and filter media — flat sheets, discs and panels. Titanium is one of the five metals we photo-etch — stainless steel, titanium, copper, brass and nickel. We do not etch aluminium.
- The aperture is the specification. An etched mesh is defined by three numbers on the drawing: aperture size, pitch and open area. All three are set by the photographic artwork, so they are identical from the first piece to the hundredth.
- The aperture floors at roughly 0.8–1.2× the material thickness. On 0.05 mm stock that is roughly a 0.04–0.06 mm aperture; on 0.1 mm stock, roughly 0.08–0.12 mm; on 0.2 mm stock, roughly 0.16–0.24 mm. Finer filtration needs thinner stock, not a harder etch — and below that, another process.
- Etched mesh is a pre-filter, not a fine filter. It does not do 5-micron or 20-micron duty. In the BRO900 those are the PP filter and membrane stages. Etched mesh is the stage that protects them.
- Titanium earns its place in seawater and corrosive streams. Its passive oxide layer is why it is specified where a mesh must sit in seawater or a chemical process stream for months without corroding into a replacement.
- Flat parts only, to 600 × 1,450 mm. We etch flat sheets; full size only at 0.5 mm and above, thinner gauges run smaller. A mesh that must be formed into a cylinder or a cone is a formed part: bending/forming is outsourced and must be confirmed at quotation.
Specifications
- Materials: stainless steel, titanium, copper, brass and nickel (we do not etch aluminium)
- Titanium grades etched: commercially pure Grades 1 and 2 and alloy Grade 5 (Ti-6Al-4V); other grades confirm at quotation
- Thickness range: 0.05–2.5 mm — gauges 0.05, 0.08, 0.1, 0.12, 0.15, 0.2, 0.25, 0.3, 0.4 and 0.5 mm stocked; above 0.5 mm up to 2.5 mm sourced per order. Mesh and filter media typically sit at 0.05–0.5 mm; support screens at 0.3–1.0 mm
- Aperture rule (through-holes, the mesh opening): ≈ 0.8–1.2× material thickness minimum — on 0.05 mm stock roughly 0.04–0.06 mm; on 0.1 mm stock roughly 0.08–0.12 mm; on 0.2 mm stock roughly 0.16–0.24 mm; on 0.3 mm stock roughly 0.24–0.36 mm (55 × 180 µm through-slots in 0.3 mm stock declined as below the rule)
- Aperture shape: round, square, slot or custom pattern — set by the artwork, not by a tool
- Pitch and open area: set by the artwork — aperture size, pitch and pattern together fix the open area. State all three on the drawing; no open-area figure is offered without them
- Maximum flat sheet: 600 × 1,450 mm — full size only at 0.5 mm and above; thinner gauges run smaller
- Tolerance: ±10% of material thickness (on 0.1 mm stock ±0.01 mm; on 0.2 mm stock ±0.02 mm; on 0.5 mm stock ±0.05 mm)
- Half-etch (integral frames, borders, identification, stepped relief): 50–75% of thickness, depth control ±0.05 mm
- Form: flat sheets, discs and panels only — no coil, no reel; bending/forming outsourced
- Finish: passivation available in-house; plating and surface treatment outsourced
- Documentation: material test certificate + per-run batch numbers on every order; PPAP Level 3 documentation available
- Lead time: samples 3–5 days when material is in stock (7–10 days for special material not stocked); production 7–10 days
- Commercial: no MOQ; US$100 minimum order; FOB
What etched titanium mesh is — and what it is not
There are four ways to make a metal mesh, and they are not interchangeable. A woven mesh is wire crossed over wire: flexible, cheap at volume, and very fine — but the wires can shift, the edges fray, and the aperture at any point is whatever the weave happens to be there. A punched mesh is a sheet with holes stamped through it: fast, but every hole carries a burr and a stressed edge, and the punch tool wears, so the hundredth hole is not the first. A sintered mesh is metal powder or felt fused into a porous three-dimensional layer: it filters fine, down into the micron range, but it is not a flat sheet with defined apertures — it is a depth filter. An etched mesh is a flat sheet with its apertures photographed into the metal: every opening is where the artwork put it, every opening is the same size, the edge is burr-free, and there are no loose wires to shed into the stream.
That difference decides the application. Where the job is fine filtration — 5 microns, 20 microns, the PP and membrane stages of a desalination system — etched mesh is the wrong answer, and this post will not pretend otherwise. A 20-micron aperture needs stock far thinner than the 0.05 mm floor of our stocked range, and even at 0.05 mm the thickness rule floors the aperture at roughly 0.04–0.06 mm. The honest place for etched mesh is upstream of the fine filter: the pre-filter that catches sand, shell fragments and marine debris before they reach the membrane, the support screen that holds a membrane flat without shedding fibres into it, the distribution plate that spreads flow evenly across a filter bed. Fotofab lists “precision filters and screens” among the common applications of photo-chemical etching, and that wording is exact: filters and screens, in the sense of defined apertures in a flat sheet — not membranes, not depth filters, not sintered layers.
Where the mesh earns its place
Seawater pre-filtration. This is the BRO900’s first stage, and the most direct application. Seawater carries sand, shell fragments and marine debris into any intake, and the pre-filter keeps them off the membrane. In seawater, the material question is corrosion: titanium carries its own passive oxide layer, so a mesh that must sit in seawater for months does not depend on a coating that can chip or wear. A stainless mesh can do the same job in many waters — the BRO900 uses one — but where the duty is continuous seawater exposure, or where the buyer has already seen a stainless screen pit or stain, titanium is the corrosion-first choice. Our titanium guide covers grade choice in general; for mesh, Grade 2 is the usual corrosion-first choice, Grade 5 the higher-strength choice where the screen carries a load.
Chemical process filtration. The same argument holds wherever the stream is corrosive: a mesh that must separate solids from a chemical process liquid or gas, and survive the stream it filters. The drawing must state the chemical environment, because the grade and the finish follow the environment — and because there are chemicals titanium does not suit, which is why the environment is one of the four drawing items below rather than an assumption.
Support screens under membranes and filter media. A flat etched screen that holds a membrane or a filter medium flat, distributes flow and protects it from damage — apertures at the thickness rule, burr-free so nothing punctures the medium, uniform so the flow is even.
Distribution and aperture plates. A flat plate of fine etched apertures that spreads a gas or liquid evenly — across a filter bed, a heat-exchanger face or a process vessel inlet. The cousin is the flow plate in our 11-14 heat-exchanger post, which is about flow channels in desalination and chemical plants; this post is about the apertures themselves.
Sorting and sizing mesh. Where parts or particles must be sorted by size — diamond sorting mesh is one of our established product lines — the aperture is the whole specification: every opening the same size, every opening in the same place, because a sorting mesh with a wandering aperture sorts nothing.
What is not etched mesh. A reverse-osmosis membrane, a PP depth filter, a sintered porous transport layer, a filter housing, an assembled filter unit, a pump. The 11-11 bipolar-plates post already drew the sintered line: a PEM porous transport layer is sintered titanium felt or powder, not an etched part. Sending us a housing drawing will get a polite no and a referral to the right process — which is better than a yes that ships a part that does not filter.
Aperture, pitch and open area: the three numbers that decide the mesh
A buyer who specifies a mesh by aperture alone has specified a third of it. The three numbers are aperture, pitch and open area, and they are linked: the artwork sets the aperture size and the distance between apertures, and the two together fix the open area — the fraction of the sheet that is open. Change the pitch and the open area changes with the aperture held constant; change the aperture and the pitch must move or the sheet becomes too weak to handle. This is why the drawing must state all three, and why no open-area figure is offered in this post without them: an open area without an aperture and a pitch is a number without a part.
The thickness rule is the constraint that binds all three. On 0.05 mm stock the aperture floors at roughly 0.04–0.06 mm; on 0.1 mm stock, roughly 0.08–0.12 mm; on 0.2 mm stock, roughly 0.16–0.24 mm; on 0.3 mm stock, roughly 0.24–0.36 mm. A buyer who needs a 0.1 mm aperture on 0.3 mm stock has specified a part etching cannot make — the answer is thinner stock, not a harder etch — and the real case behind the rule is the 55 × 180 µm through-slot in 0.3 mm stock that was declined on exactly this ground. Our tolerances post carries the same rule for every through-feature, and the mesh is no exception: the aperture is a through-feature, and the rule applies to it first.
Tolerance rides on the same number: ±10% of thickness on every dimension — on 0.1 mm stock ±0.01 mm, on 0.2 mm stock ±0.02 mm, on 0.5 mm stock ±0.05 mm — and that tolerance applies to the aperture as well as to the sheet. State the aperture, the pitch, the open area and the tolerance the application actually needs, so the quotation answers the real question instead of the assumed one.
Cleaning and life in seawater
A mesh that cannot be cleaned is a consumable, and a mesh that can be cleaned is an asset. That is the practical difference titanium makes in a filtration system, and it is decided by two properties: the metal and the edge. Titanium’s passive oxide layer means the mesh itself does not corrode in seawater or in many process streams, so cleaning does not have to fight the mesh as well as the fouling — backflushing, ultrasonic cleaning and chemical cleaning are maintenance operations, not rescue operations. And because the apertures are etched, not punched, there is no burr to trap debris and no stressed edge to start a crack; a burr-free aperture cleans out instead of holding on to what it caught.
None of this is a promise of a service life. This post gives no service-life figure, no cleaning-cycle count and no fouling rate, because those belong to the buyer’s stream, not to the etcher’s catalogue: the same mesh lasts differently in clean seawater and in a chemical slurry. What the etcher can promise is narrower and verifiable: the aperture is where the artwork put it, the sheet is flat, the edge is burr-free, and the material is the grade on the drawing, with a material test certificate and per-run batch numbers on every order. The life of the mesh is the buyer’s to measure, on the buyer’s stream, with a sample first — samples run 3–5 days when the material is in stock, and the sample is where the aperture, the cleaning and the fit are all proved at once.
What the drawing must carry
- Material and grade. Titanium, and which grade — commercially pure Grade 1 or 2, or alloy Grade 5 (Ti-6Al-4V). State it; do not leave it to the shop to guess. Other grades confirm at quotation.
- Thickness, aperture, pitch and open area. State the stock thickness, and check every aperture against it: an aperture floors at roughly 0.8–1.2× the thickness. State the aperture size, the pitch and the open area together — all three, because the artwork needs all three. On 0.1 mm stock that is roughly a 0.08–0.12 mm aperture; on 0.2 mm stock, roughly 0.16–0.24 mm. A 55 × 180 µm through-slot in 0.3 mm stock was declined on this ground — finer filtration needs thinner stock, not a harder etch, and below the rule it needs another process.
- Tolerance, finish and environment. Tolerance is ±10% of thickness on every dimension — on 0.1 mm stock ±0.01 mm, on 0.5 mm stock ±0.05 mm. State the finish: passivation in-house, or plating/surface treatment outsourced. State the stream the mesh must live in — seawater, which chemical, what temperature — because the grade and the finish follow the environment, and because there are streams titanium does not suit.
- Inspection and cleaning. State what is measured and how: aperture size and pitch, flatness, thickness, edge condition. State how the mesh will be cleaned in service, so the design can allow for it. Per-run batch numbers and a material test certificate come with every order; PPAP Level 3 is available where the programme requires it.
Frequently asked questions
Can etched titanium mesh do 20-micron filtration?
No. A 20-micron aperture needs stock far thinner than the 0.05 mm floor of our stocked range. In the BRO900, 20-micron duty is the PP filter and membrane stages. Etched mesh is the pre-filter that protects them.
Why titanium instead of stainless steel for a mesh?
Corrosion in seawater and chemical streams. Titanium carries its own passive oxide layer, so a mesh that must sit in seawater for months does not depend on a coating. Stainless steel does the same job in many waters — the BRO900’s first stage is a stainless mesh — but where the duty is continuous seawater exposure, titanium is the corrosion-first choice.
Etched mesh or woven mesh?
Woven mesh can be finer and is flexible, but its wires can shift and its edges fray, and the aperture varies across the weave. Etched mesh is one flat sheet: every aperture is where the artwork put it, every aperture is the same size, the edge is burr-free and nothing sheds into the stream. Where uniformity and cleanability matter more than fineness, etched wins; where fineness below the thickness rule matters, woven or sintered wins.
What is the difference from a sintered mesh or a porous transport layer?
A sintered layer is metal powder or felt fused into a porous three-dimensional structure — a depth filter. An etched mesh is a flat sheet with defined apertures. A PEM porous transport layer is sintered titanium felt or powder, not an etched part — see our 11-11 bipolar-plates post.
How large a mesh sheet can you etch?
Flat sheets to 600 × 1,450 mm, full size only at 0.5 mm and above; thinner gauges run smaller. A mesh that must be formed into a cylinder or a cone is a formed part — bending/forming is outsourced and must be confirmed at quotation.
Can you supply the complete filter or the desalination unit?
No. We supply the flat etched mesh, discs and panels. Housings, membranes, pumps and assembled filter units are other suppliers’ parts. Send the mesh drawing and it will be quoted; send the unit drawing and it will be declined with a referral.
How fast can we get a first article?
Samples in 3–5 days when the material is in stock, 7–10 days for special material not stocked; production 7–10 days. No MOQ, US$100 minimum order, FOB.
The mesh in a filtration system is the part nobody photographs and everybody depends on: it is the first thing the stream meets, and if it fails, everything downstream fails with it. Etched titanium mesh earns that place where the aperture must be exact, the sheet must be flat, the edge must be clean and the metal must survive the stream — and it gives way, honestly, where the filtration must go finer than the thickness rule allows. Send the drawing with the aperture, the pitch and the open area on it, prove it with a sample on the buyer’s stream, and the mesh that goes into the system is the mesh the system was designed around.
- What Does a 770 W/cm² GPU Hotspot Mean for the Etched Copper Flow Layer? - November 22, 2026
- Photo-Etched Precision Medical Metal Components: Micro-Needles, Lancets and Microfluidic Parts - November 21, 2026
- Custom Lead Frame Etching for IC Packaging: Photo-Etched vs Stamped Lead Frames - November 18, 2026








